Thumb Switch Actuator X8914

$2.99

Genuine OEM thumb switch actuator (part# X8914) for Tornado and Powr-Flite commercial high-speed burnishers — the moulded lever the operator presses to run the machine. Fits all Tornado Brute Force burnishers (see full list below).

The X8914 is the thumb switch actuator in the handle-top control group of the Brute Force burnishers. It appears on every drawing in the book, on the Brute Force 1600 (98458B), on the Brute Force 2000 (98482B), and on the current and earlier Brute Force 2000 Dust Control (98486) drawings, listed with its return spring (X8915) and near the momentary switch (X1039).

This is the part the operator touches every time the machine runs. It transfers thumb pressure into the momentary switch behind it, and because the switch is a deliberately short-travel component, the actuator has to locate accurately and return cleanly — it is what gives the control its dead-man behaviour, where releasing it stops the machine.

Replace the X8914 if it is cracked, if the pivot or its locating features are worn so it rattles or sits crooked, if it binds, or if it no longer returns fully when released. That last symptom is the important one: an actuator that stays partly depressed can keep the switch made, which is a safety fault on a machine designed to stop the instant the operator lets go. Test it off-load with the machine unplugged — the actuator should return crisply under its own spring every time.

Replace the actuator spring (X8915) with it; the two are listed at consecutive callouts and a tired spring will make a new actuator feel just as vague as the old one. If the action is good but the machine runs intermittently, the momentary switch (X1039) is the more likely culprit. The actuator is shared across the Brute Force line and carries no model name. Call 763-535-0770 if you want the control set listed for your machine. It is a shared part used across Tornado and Powr-Flite machines — see the full list of models below.

Compatible Models

  • Tornado models:
  • Powr-Flite models:
    • B171
    • B172
    • B201
    • B202
    • C131
    • C131G
    • C171
    • C171HD
    • C171HDG
    • C171SD
    • C172
    • C201
    • C201HD
    • C202
    • C202G
    • NM1600
    • NM171HD
    • NM171SD
    • NM2000
    • NM2000DC
    • NM201HD
    • NM202

Frequently asked questions

What does the thumb switch actuator (part# X8914) do on a burnisher?

It is the lever the operator presses with the thumb; it transfers that pressure into the momentary switch and returns when released, which is what makes the control dead-man operated.

How do I know if my X8914 thumb switch actuator needs replacing?

Replace it if it is cracked, rattles or sits crooked, binds, or does not return fully when released. An actuator that stays partly depressed can keep the switch made, which is a safety fault.

Should I replace the spring too?

Yes. The actuator spring (X8915) is listed at the next callout and a tired spring makes a new actuator feel just as vague as the old one.

What models is the thumb switch actuator (part# X8914) compatible with?

All three Tornado Brute Force burnishers: the 1600 (98458B), the 2000 High-Speed Glazer (98482B) and the 2000 Dust Control (98486).

How do I order the thumb switch actuator (part# X8914) or get help?

You can add the thumb switch actuator (part# X8914) directly to your cart on this page, or call us at 763-535-0770. Our staff at 5415 West Broadway, Crystal, MN 55428 can help you find the right part for your machine.

Reviews

There are no reviews yet

Be the first to review “Thumb Switch Actuator X8914”

Your email address will not be published. Required fields are marked *