Tornado Pac-Vac Aircomfort Motor D123-5300

The Tornado Pac-Vac Aircomfort motor (part# D123-5300) is the genuine Tacony OEM vacuum motor fitted to the Tornado Pac-Vac 6 Aircomfort (Model 93012) and the Tornado Pac-Vac 10 Aircomfort (Model 93014) commercial backpack vacuums. It is the single-stage bypass motor that sits inside the motor compartment behind the filter plate and generates all of the suction the machine produces.

Compatible Models for the Tornado Pac-Vac Aircomfort Motor

• Tornado Pac-Vac 6 Aircomfort — Model 93012
• Tornado Pac-Vac 10 Aircomfort — Model 93014

Fitment confirmed from the Tacony PartSmart Where Used record, which lists this motor on the Main Assembly of both the 93012 and the 93014 and on no other machine. Please note this is not the same motor used in the CleanMax CMBP-6.2 backpack, which takes part# D123-5310 — the two numbers are one digit apart and are not interchangeable. If you are not certain which machine you have, check the data label on the canister or call us and we will confirm it for you.

When the Tornado Pac-Vac Aircomfort motor needs replacing

A failing backpack vacuum motor rarely stops dead without warning. The usual sequence is a gradual loss of suction that new bags and fresh filters do not fix, followed by a change in pitch — a rising whine or a rougher, louder note than the machine used to make. Brush noise, a burning smell, visible carbon dust around the motor shroud, or a machine that runs for a few minutes and then cuts out on its thermal protection switch all point at the motor rather than at the airflow path.

Before condemning the motor, rule out the cheap causes first: a full bag, a clogged HEPA filter (B352-5200) or post filter (B352-2400), a split stretch hose, or a body seal that is no longer sealing. Restricted airflow is the single most common reason these motors fail early, because the motor relies on the through-flow of air for its own cooling. A machine that has been run repeatedly on a loaded filter will shorten the life of any replacement motor you fit, so change the filtration at the same time.

Fitting notes

The motor is accessed by removing the motor cap and the top motor shroud, and it seats against the motor seal and the bottom motor shroud. Replace the motor seal (B352-5500) and both shroud seals whenever the motor comes out — a compressed or torn seal lets air bypass the filter path and robs the new motor of the cooling it needs. Take note of the wiring harness routing and the thermal protection switch position before disconnecting anything.

Twin City Vacuum has been selling and servicing Tornado equipment since 1956 and we stock this motor on the shelf in Crystal, MN. Browse the complete Tornado Pac-Vac Aircomfort parts list or all Tornado cleaning equipment parts. Manufacturer information is available at tornadovac.com.

Frequently Asked Questions

What does the motor do on the Tornado Pac-Vac Aircomfort?

The motor (part# D123-5300) is the vacuum motor that creates all of the airflow and suction on the Pac-Vac Aircomfort. It draws air through the bag, the HEPA filter and the post filter, and the same airflow cools the motor while it runs.

How do I know if my Tornado Pac-Vac Aircomfort motor needs replacing?

Loss of suction that new bags and filters do not restore, a rising whine or rough running note, a burning smell, carbon dust around the shroud, or the machine cutting out on its thermal switch after a few minutes. Confirm the bag, HEPA filter, post filter, hose and body seal are all good first — restricted airflow mimics a failing motor and is also what kills them.

What models is the motor (part# D123-5300) compatible with?

The Tornado Pac-Vac 6 Aircomfort (Model 93012) and the Tornado Pac-Vac 10 Aircomfort (Model 93014). It does not fit the CleanMax CMBP-6.2, which uses part# D123-5310.

How do I order the motor (part# D123-5300) or get help?

You can add the motor (part# D123-5300) directly to your cart on this page, or call us at 763-535-0770. Our staff at 5415 West Broadway, Crystal, MN 55428 has been servicing Tornado equipment since 1956 and can help confirm the right part for your machine.

Questions? Call us at 763-535-0770 or visit us at 5415 West Broadway, Crystal, MN 55428.