Tornado Utility Tool Jet 31400

The Tornado Utility Tool Jet 31400 is the genuine OEM spray jet for the utility hand tool supplied with the PS Series professional spotter — the drilled orifice that turns pumped solution into the tool’s spray pattern.

Compatible Models for the Utility Tool Jet

• Tornado PS Spotter 98220 — PS Series Professional Spotter (2 gal, 115V), Series G

Tornado’s factory cross-reference returns exactly one machine for this jet: the PS Spotter 98220, Series G. That is unusually narrow, and it is the complete answer rather than a truncated window — this is the jet for the utility tool that ships with this spotter, not a general-purpose fitting. Call us at 763-535-0770 with your model and serial number if you are working on a different machine.

Not shown on the drawing, and listed in two places

Two things about where this part appears, so neither reads as an error.

Tornado’s accessories table marks it Not Shown: it is a genuine item on the list but the factory chose not to give it a numbered callout, so there is no bubble on the accessories drawing pointing at it. Nothing is missing.

It is also named in the vacuum and pressure hose section, where the utility tool itself is listed with the note that 31400 is its jet. One part, cited from two assemblies — which is the normal way a parts book handles a component that belongs to a tool rather than to the machine.

One caveat we would rather state than hide: the two tables describe the tool this jet belongs to at different sizes. We are therefore not quoting a tool dimension on this listing. If you are matching a jet to a hand tool you already own, call us at 763-535-0770 with your serial number and we will confirm against the factory before you order.

What it does and how it fails

The hand tool’s performance is set almost entirely by this one small part. The orifice diameter sets the flow rate at a given pump pressure, and its internal geometry sets the spray pattern. The tool body, the trigger and the hose simply deliver pressurised solution to it.

A jet does not break. It wears, as water pushes abrasive through a small hole thousands of times, and it partially blocks as detergent and minerals dry in it between uses. Both are gradual, which is exactly what makes them easy to miss: the pattern degrades a little at a time while the pressure gauge keeps reading normal, and the operator carries on working as though nothing has changed.

On a spotter that matters more than it does on a large extractor. This tool is used for exactly the jobs where control is the point — a single spot, a small stain, an area where overwetting is the main risk. A jet that has started to throw unevenly puts solution where it was not aimed, and on spot work that can be the difference between a clean result and a ring to deal with afterwards.

When to replace it

Replace the jet if the spray is uneven, split into separate streams, lopsided, misting rather than fanning, or weaker than it was at the same pressure; if the orifice is visibly enlarged, out of round, chipped or scored; if it is scaled and a soak will not clear it; if the body is cracked or the thread is damaged; or if it has ever been cleared with wire, a pin or a drill bit.

That last one matters. Anything pushed through the orifice permanently reshapes it, and a reshaped jet sprays wrong from then on even when it looks fine immediately afterwards. Soak and back-flush instead, and if that does not clear it, fit a new one.

This is the least expensive part on the tool and the one most likely to be the problem. Check it first, not last, and keep a spare on the machine.

Fitting notes

Depressurise the system before removing the old jet, and note its orientation — a fan jet has to be clocked correctly relative to the tool head or the pattern lands across the wrong axis.

Clean the seat, fit by hand, then nip it up gently with the correct tool. The seal comes from the seat rather than from force, and these are small threaded parts in a comparatively soft body that strip easily.

Test over a drain or a bucket before using the tool on anything that matters. The pattern should be an even fan with no gaps, heavy edges or stray streams. Flush the tool with clean water at the end of the day.

Twin City Vacuum has been selling and servicing Tornado equipment since 1956.

You can browse every assembly for this machine on our Tornado PS Spotter 98220 parts page, and the manufacturer’s specifications are published at tornadovac.com.

Frequently Asked Questions

What does the Utility Tool Jet 31400 do?

It is the drilled orifice on the utility hand tool that turns pumped solution into the spray pattern. The orifice diameter sets the flow rate at a given pump pressure and its internal geometry sets the fan shape, so the jet rather than the tool body is what determines how the tool performs.

Why can I not find the Utility Tool Jet on the accessories drawing?

Because Tornado’s table marks it Not Shown. It is a genuine item on the parts list, but the factory gave it no numbered callout, so there is no bubble pointing at it on the drawing. It is also named in the vacuum and pressure hose section, where the utility tool is listed with this number as its jet — one part cited from two assemblies, not two parts. The two tables do describe that tool at different sizes, which is why we quote no tool dimension here; call us and we will confirm.

My hand tool sprays unevenly. Is the jet or the pump at fault?

Check the jet first. It is the least expensive part on the tool and by far the more common cause: a jet wears gradually as abrasive passes through it and partially blocks as detergent dries in it, both of which degrade the pattern while the pressure gauge keeps reading normally. Run the tool over a drain and look — an uneven, split, lopsided or misting fan means the jet. And never clear one with wire or a pin; that permanently reshapes the orifice.

How do I order the Utility Tool Jet (part# 31400) or get help?

You can add the Utility Tool Jet (part# 31400) directly to your cart on this page, or call us at 763-535-0770. Our staff at 5415 West Broadway, Crystal, MN 55428 has been servicing Tornado equipment since 1956 and can help confirm the right part for your machine.

Questions? Call us at 763-535-0770 or visit us at 5415 West Broadway, Crystal, MN 55428.