Washer INOX 60308007
$1.99
Genuine OEM stainless flat washer (part# 60308007), 8 x 24 x 2 mm to UNI 6593, for Tornado floor scrubbers. It is the wide-face stainless washer used at the bolted joints of the squeegee control linkage, where it spreads clamp load across the arm plates.
Genuine OEM stainless (INOX) flat washer (part# 60308007), 8 mm bore by 24 mm outside diameter by 2 mm thick, made to UNI 6593. It is used on a wide range of Tornado floor scrubbers — the full machine list is below — and on the squeegee control assembly it is the washer that turns up most often, fitted at the support arm joint, the arm joint plate and several of the bolted pivots along the linkage.
The 24 mm outside diameter is the point of this part. That is a wide face for an 8 mm bolt, and it is specified that way because the linkage arms and plates it clamps are relatively thin. A normal-series washer would concentrate the bolt load into a small ring and start to dish the plate; this wide-series washer spreads it, which is what keeps the joint flat and the geometry of the squeegee carriage true over years of service.
Stainless matters as much as the size. These joints sit in the splash zone behind the brush deck, soaked in recovery water and detergent through every shift. A plated washer corrodes there, swells with rust, loses its flat bearing face, and bonds itself to the bolt so the joint cannot be stripped without damage. Stainless stays serviceable and comes apart cleanly years later.
Inspect for dishing, for a bright polished wear ring on one face, for thinning against a new part, and for any washer that spins freely with the bolt when it should be clamped. Replace rather than reuse when a joint is rebuilt — these are inexpensive and the alternative is clamp load you cannot be sure of. Count the washers off as you strip a joint; a pivot rebuilt one washer short runs with the bolt head bearing straight on the arm.
This is the genuine Tornado part in the exact specified size, so the stack height at each joint and the resulting linkage geometry remain as designed.
Compatible Models
- Tornado BD14/4 Disc Brush Autoscrubber — 99414
- Tornado 17″ BD 17/6 Automatic Scrubber — 99617
- Tornado 20″ BD 20/11 — 99680
- Tornado 18″ BR 18/11 — 99685
- Tornado BD 22/14 — 99690
- Tornado TS350-W20-U — 99694
- Tornado BD 26/14 — 99720
- Tornado BD 26/26 — 99726
- Tornado BD 28/20 — 99728
- Tornado TS550-W28-U — 99729
- Tornado BD 32/26 — 99732
- Tornado BD 26/30 — 99760
- Tornado BR 28/30 — 99765
- Tornado BD 26/27 — 99770
- Tornado BD 26/27 — 99772
- Tornado BR 28/27 — 99775
- Tornado BD 33/30 — 99780
- Tornado BR 33/30 — 99785
- Tornado BDSO 27/28 Stand-On Scrubber — 99786 / 99786C
- Tornado BD 40/66 — 99790
- Tornado BR 40/66 — 99795
- Tornado Formerly 99680L — TS120-S45-U
- Tornado 99680blt — TS120-S53-U
- Tornado BDSO 20/21 — TS120-S59-U
- Tornado 99694 — TS350-W20-U
- Tornado TS530-W26-U
- Tornado TS530-W30-U
- Tornado 99729 — TS550-W28-U
This part is shared across 28 Tornado machines. If your machine is not listed, call 763-535-0770 and we will check it for you.
See where this part sits on the machine on the squeegee control drawing, or browse every Tornado BDSO 27/28 parts diagram.
Frequently Asked Questions
What size is the washer (part# 60308007)?
It is 8 mm bore by 24 mm outside diameter by 2 mm thick, in stainless (INOX) to UNI 6593 — a wide-series washer, deliberately larger in the face than a normal washer for an 8 mm bolt.
Why is such a wide washer used on an 8 mm bolt?
Because the linkage arms and plates it clamps are relatively thin. A normal-series washer would concentrate the bolt load into a small ring and dish the plate; the wide face spreads it so the joint stays flat and the squeegee carriage keeps its geometry.
How do I know if the washer (part# 60308007) needs replacing?
Replace it if it has dished instead of staying flat, has a bright polished wear ring on one face, is visibly thinner than a new one, or spins freely with the bolt when the joint should be clamped. Fit new washers whenever a joint is rebuilt.
How do I order the Washer INOX (part# 60308007) or get help?
You can add the Washer INOX (part# 60308007) directly to your cart on this page, or call us at 763-535-0770. Our staff at 5415 West Broadway, Crystal, MN 55428 has been servicing Tornado equipment since 1956 and can help confirm the right part for your machine.
Manufacturer specifications for the Tornado BDSO 27/28 stand-on scrubber are published by Tornado Industries at tornadovac.com. If you are not certain the washer inox (part# 60308007) is the right part for your machine, call Twin City Vacuum at 763-535-0770 or stop in at 5415 West Broadway, Crystal, MN 55428 — we have been servicing commercial floor equipment since 1956.






Reviews
There are no reviews yet