Tornado Internal Cord 14/3 x 49 in. SJTWA X8022
$23.99
Genuine OEM 14/3 x 49 in. SJTWA internal cord (part# X8022) for commercial high-speed burnishers — the internal lead that runs between the switch at the handle and the motor. Fits all Tornado Brute Force burnishers (see full list below).
The X8022 is a 49 inch length of 14/3 SJTWA cord used inside the machine, between the handle-top switch group and the motor. It appears on every drawing in the Brute Force burnisher book, on the Brute Force 1600 (98458B), on the Brute Force 2000 (98482B), and on both Brute Force 2000 Dust Control (98486) drawings — in each case listed with the cord hook, the strain relief parts and the 75 foot supply cord. It is a shared part used across Tornado machines — see the full list of models below.
SJTWA is a junior-service, thermoplastic, water-resistant jacket rated for outdoor use, and 14 gauge three-conductor is what a 115V burnisher motor circuit needs. This internal lead is the conductor that has to survive being flexed at the handle pivot every time the handle angle is changed, which makes it a genuine wear item rather than permanent wiring.
Replace the X8022 if the jacket is cut, chafed, cracked or heat-damaged anywhere along its length, if any conductor is exposed, if a terminal end is burnt or discoloured, or if the machine has an intermittent fault that moves when the handle is flexed. That last symptom — a machine that cuts out when the handle is moved and runs when it is held still — is a broken conductor inside the jacket, and it is the one fault that cannot be found by looking. Replace the cord; do not splice it.
When fitting a new internal cord, renew the grommet (7BG004) in the handle at the same time and make sure the jacket is not pinched where the handle closes. The part is shared across the Brute Force line and carries no model name. Call 763-535-0770 with your model and serial number if you want it listed before ordering.
Compatible Models
- Tornado models:
- P Series 17″ Floor Machine With Pad Holders (115V) — 97562
- 17″ — 97562B
- P Series 17″ Floor Machine With Pad Holders (230V) — 97563
- P Series 20″ Floor Machine With Pad Holders (115V) — 97564
- 20″ — 97564B
- P Series 20″ Floor Machine With Pad Holders (230V) — 97565
- P Series 1600 Glazer (115V) — 98458
- Brute Force 1600 — 98458B
- P Series 1600 Glazer (230V) — 98459
- P Series 2000 Glazer (115V) — 98482
- Brute Force 2000 High-Speed Glazer — 98482B
- Brute Force 2000 High-Speed Glazer with Dust Control — 98486
- P Series 2000 Glazer (230V) — 98487
Frequently asked questions
What does the 14/3 x 49 in. cord (part# X8022) do on a burnisher?
It is the internal lead that carries power between the handle-top switch group and the motor, flexing at the handle pivot as the handle angle is changed.
How do I know if my X8022 internal cord needs replacing?
Replace it if the jacket is cut, chafed, cracked or heat-damaged, if any conductor shows, if a terminal end is burnt, or if the machine cuts out when the handle is flexed and runs when it is held still.
Can I splice a broken internal cord instead of replacing it?
No. A splice inside a cord that flexes at the handle pivot every time the machine is used will fail again, and a joint in a flexing conductor is a fire and shock risk. Fit a new cord.
What models is the 14/3 x 49 in. SJTWA cord (part# X8022) compatible with?
All three Tornado Brute Force burnishers: the 1600 (98458B), the 2000 High-Speed Glazer (98482B) and the 2000 Dust Control (98486).
How do I order the 14/3 x 49 in. cord (part# X8022) or get help?
You can add the internal cord (part# X8022) directly to your cart on this page, or call us at 763-535-0770. Our staff at 5415 West Broadway, Crystal, MN 55428 can help you find the right part for your machine.






Reviews
There are no reviews yet