Tornado Screw 3/8-16 x 3/4 in. X8223
$2.99
Genuine OEM 3/8-16 x 3/4 in. screw (part# X8223) for commercial high-speed burnishers — the largest-diameter fastener on the Brute Force drawings. Fits all Tornado Brute Force burnishers (see full list below).
The X8223 is a 3/8-16 screw, 3/4 inch long, and at 3/8 inch diameter it is the heaviest thread used anywhere on the Brute Force burnisher drawings. It appears on all four: on the Brute Force 1600 (98458B), on the Brute Force 2000 (98482B), and on both Brute Force 2000 Dust Control (98486) drawings, in the group with the washer X8230 and the nut X8231. It is a shared part used across Tornado machines — see the full list of models below.
A 3/8-16 fastener is specified where the load is real. The clamping force a 3/8 inch coarse thread can hold is roughly double that of a 5/16 inch screw, which is why the book reserves it for the few positions that carry the heaviest loads on the machine rather than using it throughout.
Replace the X8223 if the threads are galled or stretched, if the drive feature is damaged, or if the fastener has been through a joint that came loose — a screw that has worked loose and then been re-torqued repeatedly has usually yielded slightly and will not hold the same preload again. Thread engagement is the thing to get right on reassembly: run it in by hand for the first few turns, and if it will not start cleanly, stop and check the female thread rather than forcing it.
Fit it together with the washer (X8230) and nut (X8231) shown at the same group of callouts; those three parts are specified as a set and the washer stack is part of the joint design. The screw is shared hardware across the Brute Force burnisher line, so it carries no model name. Call 763-535-0770 with your model and serial number if you want the hardware at a callout listed.
Compatible Models
- Tornado models:
- P Series 1600 Glazer (115V) — 98458
- Brute Force 1600 — 98458B
- P Series 1600 Glazer (230V) — 98459
- P Series 2000 Glazer (115V) — 98482
- Brute Force 2000 High-Speed Glazer — 98482B
- Brute Force 2000 High-Speed Glazer with Dust Control — 98486
- P Series 2000 Glazer (230V) — 98487
Frequently asked questions
Where is the 3/8-16 x 3/4 in. screw (part# X8223) used on a Brute Force burnisher?
It appears on the Brute Force 1600 (98458B), on the Brute Force 2000 (98482B) and on both 98486 drawings, grouped with washer X8230 and nut X8231.
Why is this fastener larger than the others on the drawing?
A 3/8-16 thread holds roughly twice the clamping force of a 5/16 inch screw, so the book uses it only at the few positions that carry the heaviest loads rather than throughout the machine.
How do I know if my X8223 screw needs replacing?
Replace it if the threads are galled or stretched, if the drive feature is damaged, or if it has been repeatedly re-torqued after working loose — it will have yielded and will not hold the same preload.
What models is the 3/8-16 x 3/4 in. screw (part# X8223) compatible with?
All three Tornado Brute Force burnishers: the 1600 (98458B), the 2000 High-Speed Glazer (98482B) and the 2000 Dust Control (98486).
How do I order the 3/8-16 x 3/4 in. screw (part# X8223) or get help?
You can add the screw (part# X8223) directly to your cart on this page, or call us at 763-535-0770. Our staff at 5415 West Broadway, Crystal, MN 55428 can help you find the right part for your machine.






Reviews
There are no reviews yet