Screw M4 x 12 60140403

$1.99

Genuine OEM M4 x 12 mm screw (part# 60140403) for Tornado floor scrubbers. It is the short M4 used where a control panel component bolts down directly.

Genuine OEM M4 x 12 mm screw (part# 60140403) for Tornado floor scrubbers — the machines it fits are listed below. On the control panel it fastens a component directly to its mounting, with nothing stacked in between.

The control panel area uses M4 at more than one length, and the lengths are not interchangeable. Behind a panel there is very little free space and a great deal of wiring, so a screw that is longer than intended can press into a harness, a connector or the back of a board — damage that is invisible from the front and shows up weeks later as an intermittent fault. In a shallow blind boss, a long screw simply bottoms out, so the driver reads tight while the component is still loose.

M4 also has little margin in itself. The drive recess rounds off if the driver is not an exact fit, the thread strips easily, and in a plastic boss the host thread almost always fails before the screw does. Tighten to seat rather than to feel, and if a joint will not hold, inspect the boss before fitting another screw.

Replace a screw whose drive recess is damaged, whose thread is galled, or whose shank is bent — a bent M4 holds its component crooked, which on a panel means a switch that no longer sits square to its hole and operates unevenly.

Fit any washer the assembly calls for: under a small head, the load is concentrated enough to dent a panel or crack a board.

Compatible Models

  • Tornado BD 28/20 — 99728
  • Tornado BD 32/26 — 99732
  • Tornado BD 26/27 — 99770
  • Tornado BD 26/27 — 99772
  • Tornado BR 28/27 — 99775
  • Tornado BD 33/30 — 99780
  • Tornado BR 33/30 — 99785
  • Tornado BDSO 27/28 Stand-On Scrubber — 99786 / 99786C
  • Tornado BDSO 20/21 — TS120-S59-U
  • Tornado TS530-W26-U
  • Tornado TS530-W30-U

This part is shared across 11 Tornado machines. If your machine is not listed, call 763-535-0770 and we will check it for you.

See where this part sits on the machine on the control panel drawing, or browse every Tornado BDSO 27/28 parts diagram.

Frequently Asked Questions

Where is the screw (part# 60140403) used?

On the control panel, fastening a component directly to its mounting with nothing stacked in between. It is the short M4 — the area uses more than one length.

What happens if I use a longer M4?

Behind a panel there is very little space and a lot of wiring, so a longer screw can press into a harness, a connector or the back of a board — damage invisible from the front that shows up weeks later as an intermittent fault. In a blind boss it just bottoms out.

The screw will not hold. What should I check?

The boss it threads into. In plastic the host thread almost always fails before the screw does. Also fit whatever washer the assembly calls for — under a small head the load is concentrated enough to dent a panel or crack a board.

How do I order the Screw M4 x 12 (part# 60140403) or get help?

You can add the Screw M4 x 12 (part# 60140403) directly to your cart on this page, or call us at 763-535-0770. Our staff at 5415 West Broadway, Crystal, MN 55428 has been servicing Tornado equipment since 1956 and can help confirm the right part for your machine.

Manufacturer specifications for the Tornado BDSO 27/28 stand-on scrubber are published by Tornado Industries at tornadovac.com. If you are not certain the screw m4 x 12 (part# 60140403) is the right part for your machine, call Twin City Vacuum at 763-535-0770 or stop in at 5415 West Broadway, Crystal, MN 55428 — we have been servicing commercial floor equipment since 1956.

Reviews

There are no reviews yet

Be the first to review “Screw M4 x 12 60140403”

Your email address will not be published. Required fields are marked *