Screw #10-24 x 3/4 in 04735

The Screw #10-24 x 3/4 in (part# 04735) is a genuine Tacony OEM Phillips truss-head screw in zinc plate, listed at (Model 93030). It is a widely shared Tacony fastener — it is already used in our catalogue on the Tornado Marathon SE 900 brush assembly and on the Powr-Flite PFX900S. It also fits the Tornado 98168 20″ Marathon 1200 carpet extractor (12 Gallon 115V), Series B, C, D and E.

The truss head is the distinguishing feature. It is broader and shallower than a pan or round head, which gives a much larger bearing footprint for the same thread size and keeps the profile low. Tacony uses it where a screw has to clamp a thin panel or a soft moulding without pulling through, and where a taller head would foul something moving nearby. Swapping in a pan-head screw of the same thread and length is the usual mistake; it will hold, but on a thin panel it concentrates load over a smaller circle and can dimple or crack it.

At 3/4 in this screw is picking up a good depth of thread, so it is generally found in fastenings that matter. Replace any with a cammed-out recess, a galled or stripped thread, or a shank that has bent. If the screw spins without drawing tight, inspect the thread it runs into before refitting — in a moulding, the female thread usually fails first.

Compatible Models for the Screw #10-24 x 3/4 in

• Tornado 93030 30″ Clean-Air Carpetkeeper (Wide Area) — Series G
• Tornado Marathon SE 900 (Model 98170)
• Powr-Flite Prowler PFX900S
• Powr-Flite Prowler PFX900SG
• Tornado 98168 20″ Marathon 1200 Carpet Extractor (12 Gallon 115V) — Series B, C, D and E

This is a common Tacony fastener used on many machines beyond the models listed. Fits many Tacony models — call 763-535-0770 to confirm fitment for your machine.

Many Tacony fasteners are shared more widely across the Tornado, CleanMax, Riccar, Simplicity and Powr-Flite ranges; if your machine is not listed, call 763-535-0770 and we will confirm before you order.

Twin City Vacuum has been selling and servicing Tacony equipment since 1956 and stocks the genuine 04735 part rather than a hardware-store substitute. Browse the full Tornado 93030 main assembly parts, or read more on the Tornado manufacturer site.

Frequently Asked Questions

What does the Screw #10-24 x 3/4 in do on the Tornado 93030?

It is the truss-head #10-24 screw, used to clamp panels and brackets where a broad, low head is needed to spread load without pulling through thin material.

What other machines use part# 04735?

This is a shared Tacony fastener. In our catalogue it is already used on the Tornado Marathon SE 900 (Model 98170) brush assembly and on the Powr-Flite PFX900S, as well as the CK 3030 Series G. Tacony hardware is commonly shared across the Tornado, Powr-Flite, CleanMax, Riccar and Simplicity ranges.

How do I know if my Screw #10-24 x 3/4 in needs replacing?

Replace it if the Phillips recess has rounded out, the thread is stripped or galled, or the shank is bent. Also replace one that will no longer pull its panel tight, and check the receiving thread at the same time.

How do I order the Screw #10-24 x 3/4 in (part# 04735) or get help?

You can add the Screw #10-24 x 3/4 in (part# 04735) directly to your cart on this page, or call us at 763-535-0770. Our staff at 5415 West Broadway, Crystal, MN 55428 has been servicing Tacony equipment since 1956 and can help confirm the right part for your machine.

Questions? Call us at 763-535-0770 or visit us at 5415 West Broadway, Crystal, MN 55428.