Tornado Brute Force 1600 98458B Motor Pulley X8889
$45.99
Genuine OEM motor pulley (part# X8889) for the Tornado Brute Force 1600 Burnisher, Model 98458B — the drive pulley on the motor shaft. Shown on the main assembly drawing.
The X8889 is the pulley fitted to the motor shaft on the Brute Force 1600 burnisher (Model 98458B). It is on that machine’s main assembly drawing. It is specific to the 1600: the Brute Force 2000 machines (98482B and 98486) use a different motor pulley, the X9298 O-groove pulley, which is one of the parts that makes the 1600 a 1,600 RPM machine and the 2000 a 2,000 RPM machine. That difference is why this listing names the model. It is a shared part used across Tornado machines — see the full list of models below.
The motor pulley is the drive end of the belt system. Its effective diameter, together with the main pulley’s, sets the pad speed the machine runs at, and its groove has to grip the V-belt over the whole flank to deliver full torque from a standing start. It also runs hotter than the driven pulley because it is closer to the motor and turns at motor speed.
Replace the X8889 when the groove is worn wide, polished or glazed, when the flanks are chipped, when the bore or set-screw seat is worn so the pulley can creep on the shaft, or when there is visible run-out. A pulley creeping on the motor shaft is the one failure that can damage the shaft itself, so a set screw that will not hold deserves attention straight away rather than another turn of the wrench. Belt squeal on start-up, short belt life and black belt dust in the housing all point at pulley condition.
Fit a new V-belt (X8099-5) whenever you change a pulley, and check the main pulley (X8096) at the same time — a worn pair will destroy a new belt. Do not substitute a 2000-series pulley to make the machine faster: pad speed on a burnisher is matched to the motor and the pad system, and overspeeding is how you burn floors and cook motors. Call 763-535-0770 with your model and serial number if you want it listed before ordering.
Compatible Models
- Tornado models:
- P Series 1600 Glazer (115V) — 98458
- Brute Force 1600 — 98458B
- P Series 1600 Glazer (230V) — 98459
Frequently asked questions
What does the motor pulley (part# X8889) do on the Tornado 98458B?
It is the drive pulley on the motor shaft. With the main pulley it sets the pad speed and transmits motor torque to the V-belt.
How do I know if my X8889 motor pulley needs replacing?
Replace it if the groove is worn wide, polished or glazed, if the flanks are chipped, if the bore or set-screw seat lets the pulley creep on the shaft, or if there is visible run-out. Belt squeal and short belt life are the usual symptoms.
Can I fit the 2000-series pulley to make my 1600 faster?
No. Pad speed is matched to the motor and the pad system; overspeeding a burnisher damages floor finish and shortens motor life. The 98458B uses the X8889 and the 2000 machines use the X9298.
What models is the motor pulley (part# X8889) compatible with?
The Tornado Brute Force 1600 Burnisher, Model 98458B. The Brute Force 2000 machines (98482B and 98486) use the X9298 motor pulley instead.
How do I order the motor pulley (part# X8889) or get help?
You can add the motor pulley (part# X8889) directly to your cart on this page, or call us at 763-535-0770. Our staff at 5415 West Broadway, Crystal, MN 55428 can help you find the right part for your machine.






Reviews
There are no reviews yet