Every Tornado BDSO 20/21 parts diagram in one place. The BDSO 20/21 is a stand-on disc scrubber sold as the TS120-S59-UC (lead acid), the TS120-S59-UG (AGM) and the TS120-S59-UE (TPPL) — all three share these assemblies. Can’t find your part? Call us at 763-535-0770.
Pick the assembly below, then click a numbered hotspot on the drawing or the matching row in the parts table to open that part. Where Tornado revised an assembly during production, every revision appears on the same page in serial order, oldest first, with the serial range stated above each drawing — so check the serial number on your machine’s data plate before you order.
Brush Base37 parts · 1 drawing
Drive Wheel53 parts · 1 drawing
Foot Board22 parts · 1 drawing
Central Frame34 parts · 4 drawingsWhat the Tornado BDSO 20/21 parts diagrams cover
The twenty-four assemblies above are the complete factory parts book for the machine. Between them they account for every fastener, hose, bearing, switch and casting Tornado fits to the BDSO 20/21, which is why the Tornado BDSO 20/21 parts you need are almost always on one of these pages rather than in a generic scrubber listing. The drawings are the manufacturer’s own, reproduced at full resolution, with each callout number on the drawing linked to the part it belongs to.
The machine scrubs a 20-inch path at up to 22,000 square feet per hour, applies 48.5 pounds of down pressure at 140 RPM and turns inside a 53-inch radius. Down pressure is what drives wear here: the pad driver or brush, the brush base bearings and the squeegee blades go first, followed by the solution valve, the vacuum motor filter and the drive wheel. Those Tornado BDSO 20/21 parts are the ones worth keeping on the shelf if the machine runs daily.
Serial numbers matter on nine of these assemblies
The central frame, brush base control, suction assembly, squeegee, frame, control panel, solution tank, squeegee support and electrical layout were each revised mid-production. Rather than splitting those into separate pages, every version sits on one page in serial order with its range labelled above the drawing, so you can compare the old and new parts side by side. Ordering Tornado BDSO 20/21 parts from the wrong serial block is the single most common mistake on this machine — the data plate settles it in a few seconds.
Parts we do not stock
Where a callout on a drawing is a part the factory does not sell separately, or one we do not carry, the row stays on the table and is marked call-us instead of being deleted. That keeps the numbering on the table identical to the numbering on the drawing, and it means a part you cannot add to the cart is still a part we can usually source. Call 763-535-0770 with the callout number and your serial number and we will tell you what the factory book shows.
Shop the Tornado BDSO 20/21 parts category, view the BDSO 20/21 stand-on scrubber itself, or compare the larger Tornado BDSO 27/28 parts diagrams. Manufacturer specifications are published at tornadovac.com. We have been servicing commercial floor equipment at 5415 West Broadway, Crystal, MN 55428 since 1956.
Tornado BDSO 20/21 parts: frequently asked questions
How many parts diagrams does the Tornado BDSO 20/21 have?
The factory book runs to 38 drawings, which we group into 24 assembly pages. Nine of those assemblies were revised during production, so their pages carry more than one drawing, each labelled with the serial range it applies to.
Do the TS120-S59-UC, TS120-S59-UG and TS120-S59-UE use the same parts?
Largely yes. The three differ by battery type – lead acid, AGM and TPPL – so the battery, charger and electrical-layout assemblies vary. The frame, brush base, squeegee, tanks and recovery system are common to all three.
How do the hotspot diagrams work?
Each numbered callout on the drawing is clickable and opens that part in a new tab. The parts table below the drawing repeats the same numbers in order, so you can work from either the picture or the list.
Can you supply a Tornado BDSO 20/21 part that is not listed on these pages?
Usually. Rows marked call-us are parts we do not stock but can normally order from the factory book. Call 763-535-0770 with your model, serial number and the callout number from the drawing.
