Find genuine Tornado BDSO 27/28 replacement parts for Models 99786 and 99786C. Can’t find your part? Call us at 763-535-0770.
Find the item number on the drawing, then match it to the same number in the table below that drawing. Each table lists the part description and Tornado’s part number for every numbered item on that sheet.
Lower Cover Drawing
Tornado publishes one drawing for this assembly, covering every BDSO 27/28 serial number.
1. Blue LED – 637100401. Blue LED – 6371004010. Screw M8 x 25 INOX – 6011080811. Lock Washer INOX – 6050800612. Washer INOX – 6030800713. Side Support Cover – 2151102014. Washer INOX – 6030800715. Lock Washer INOX – 6050800616. Screw M8 x 25 INOX – 601108082. Bushing – 471031303. Conical Washer – 605140014. Lower Cover – 215110105. Front Support Cover – 215110306. Screw M8 x 35 – 601008067. Screw M8 x 25 INOX – 601108088. Lock Washer INOX – 605080069. Washer INOX – 60308007The lower cover closes in the underside of the BDSO 27/28 and keeps water, dirt and debris out of the components behind it. It is a simple assembly — the cover itself, its gasket or seal where one is used, and the fasteners — but a missing or ill-fitting lower cover lets dirty water reach wiring and bearings it was never meant to touch. Covers crack at their mounting points first, usually after an impact or after being refitted with the wrong hardware. Tornado publishes a single lower cover drawing for the whole BDSO 27/28 production run.
| # | Image | Part Description | Part Number | Price |
|---|---|---|---|---|
| 1 | Spot Light w/Terminals | 63710041 | Call 763-535-0770 | |
| 1 | Blue LED | 63710040 | Call 763-535-0770 | |
| 2 | Bushing | 47103130 | Call 763-535-0770 | |
| 3 | Conical Washer | 60514001 | Call 763-535-0770 | |
| 4 | Lower Cover | 21511010 | Call 763-535-0770 | |
| 5 | Front Support Cover | 21511030 | Call 763-535-0770 | |
| 6 | Screw M8 x 35 | 60100806 | Call 763-535-0770 | |
| 7 | ![]() | Screw M8 x 25 INOX | 60110808 | $1.99 |
| 8 | ![]() | Lock Washer INOX | 60508006 | $1.99 |
| 9 | ![]() | Washer INOX | 60308007 | $1.99 |
| 10 | ![]() | Screw M8 x 25 INOX | 60110808 | $1.99 |
| 11 | ![]() | Lock Washer INOX | 60508006 | $1.99 |
| 12 | ![]() | Washer INOX | 60308007 | $1.99 |
| 13 | Side Support Cover | 21511020 | Call 763-535-0770 | |
| 14 | ![]() | Washer INOX | 60308007 | $1.99 |
| 15 | ![]() | Lock Washer INOX | 60508006 | $1.99 |
| 16 | ![]() | Screw M8 x 25 INOX | 60110808 | $1.99 |
Frequently Asked Questions About the Tornado BDSO 27/28 Lower Cover
Does it matter if I run the machine without the lower cover?
Yes. The cover is what keeps recovery water and debris away from wiring and bearings underneath. Running without it shortens the life of parts that are far more expensive than the cover.
My cover will not sit flush any more. What should I replace?
Check the mounting points on the cover itself for cracks, and check that the fasteners are the ones on this drawing. Over-long or over-tightened fasteners distort the cover and are a common cause of poor fit.
Is the lower cover different on later machines?
No. Tornado publishes one lower cover drawing covering all BDSO 27/28 serial numbers.
Not sure which lower cover part your machine takes? Call 763-535-0770 with the serial number from the data plate, or stop in at 5415 West Broadway, Crystal, MN 55428 — we have sold and serviced commercial floor equipment since 1956. You can also go back to all Tornado BDSO 27/28 parts diagrams or browse the Tornado BDSO 27/28 parts category.



