Find genuine Mytee 1000DX-200 Speedster and 2005CS Contractor’s Special vacuum tank, motor and switch parts. Can’t find your part? Call us at 763-535-0770.
This drawing is tall, so it is shown at 700 pixels wide on this page; the clickable dots are placed and checked at that width.
Click on any numbered part in the diagram below to go directly to that part’s product page.
60. Speedster Vacuum Tank – P74861. 2 in Inlet Elbow Assembly – A92665. 7 in Vacuum Lid Gasket – G09166. 7 in Clear Vacuum Tank Lid – G09067. Screw #8 x 5/8 in Phillips Oval, Stainless – H30468. PVC Pipe 1-1/2 in (short) – PH633-.169. Foam Filter – G02270. 1.9 in Screen Mesh Filter – G09771. 1-1/2 in PVC Slip Adapter – P50272. PVC Pipe 1-1/2 in (7 in) – PH633-775. 1-1/2 in Steel Lock Nut – H31463. PVC Pipe 1-1/2 in (2.5 in) – PH633-2.564. 1-1/2 in 45 Degree PVC Adapter – P50363. PVC Pipe 1-1/2 in (2.5 in) – PH633-2.564. 1-1/2 in 45 Degree PVC Adapter – P50377. 2 in Vinyl Cuff-Lynx Male Starter – H135V14. 10-32 Kep Nut – H27378. Speedster Switch Plate – H34880. Dome Plug 3/8 in – H42282. 2-Position Rocker Switch – E53690. 1/4 in Brass Tee – B11387. 9/16 in ID Flat Washer – H21286. 1/4 in Brass Hex Nipple – B10791. Vacuum Shut-Off Float Switch – E37392. 1/4 in 90 Degree Brass Street Elbow – B10379. Flat Washer #8 – H61281. Screw 10-32 x 1/2 in Socket Head – H38984. Heyco Vent Plug – H43479. Flat Washer #8 – H61295. Bolt 1/4-20 x 4 in Hex, Zinc – H09647. Lock Washer 1/4 in, Stainless – H2136. 1/4 in Stainless Flat Washer – H21096. 3.25 in Vacuum Motor Spacer – H50397. 3-Stage Low-Amp Vacuum Motor – C302LA98. Vacuum Motor Gasket – G00493. Bolt 1/4-20 x 1/2 in Serrated Hex Flange – H77055. 2 x 2 in L-Bracket – H390A58. 3 in Wheel – H358B13. 12mm External C-Clip – H04259. Axle 7.94 in x 0.50 in – H50756. 45 Degree Drain Spout – H22657. 1-1/2 in Drain Valve – H22583. Switch Plug – P967A74. Gasket 1-1/2 in PVC – G22276. Starter Cuff Gasket – G22373. Bulkhead Washer 1 in – H30562. 1-1/2 in MPT PVC Adapter – P52094. Screw #10 x 5/8 in Hex Head, Zinc – H34389. 1/4 in NPT Nut – B15687. 9/16 in ID Flat Washer – H21288. Buna Hand Tool Valve Gasket – G105This drawing covers the recovery side of the Mytee 1000DX-200 Speedster. The 2005CS Contractor’s Special is the same machine as the 1000DX-200 sold as a package, so this drawing covers both.
Mytee 1000DX-200 vacuum tank parts on this drawing
It shows the vacuum tank with its drain valve and spout, the inlet elbow and PVC pipe, the screen and foam filters, the clear lid and 7-inch gasket, and the E373 vacuum shut-off level switch.
In addition, it shows the H348 switch plate with its rocker switches and the two C302LA 3-stage vacuum motors with their supports and gaskets. For example, weak suction usually starts at the lid gasket, the drain valve or a clogged filter.
However, parts marked Call are fasteners, the tank and pipe lengths that Mytee does not sell on its website, so call us and we will order them. Also, item 85, an H029 plastite screw, is listed in the book but not drawn.
Mytee 1000DX-200 / 2005CS Vacuum Tank, Motors & Switches Parts List
Frequently Asked Questions
Which vacuum motors does the 1000DX-200 use?
Two C302LA 3-stage low-amp vacuum motors, item 97 on this drawing.
What stops the 1000DX-200 from overfilling?
The E373 vacuum shut-off level switch, item 91, cuts the vacuum when the recovery tank is full.
Why do some parts say Call?
Mytee does not sell every fastener, fitting and length of hose on its website. Call 763-535-0770 with the item number from this drawing and we will order it.
How do I order 1000DX-200 or 2005CS vacuum tank parts?
Click the part on the drawing or in the table and add it to your cart, or call 763-535-0770. Our staff at 5415 West Broadway, Crystal, MN 55428 can confirm the part first.
Need other parts? See the base, pump and power inlet or the solution tank, handle and plumbing, or go back to all Mytee 1000DX-200 and 2005CS parts diagrams. You can also see the 1000DX-200 and 2005CS on mytee.com.






























