Tornado Manifold Retaining Bracket Weldment 19152

This weldment holds the spray manifold in position across the width of the machine. Where it sits determines where the solution lands, and where the solution lands determines whether the brush and the nozzle get to do their jobs properly. Part number 19152 is the genuine OEM manifold retaining bracket weldment for the MWH-800, Marathon 800 and Marathon 1200 extractors.

Compatible Models for the Manifold Retaining Bracket Weldment

This part fits the following Tornado machines:

• Tornado 98164 MWH-800 8-Gallon Self-Contained Carpet Extractor
• Tornado 98166 20″ Marathon 800 Carpet Extractor (8 Gallon, 115V)
• Tornado 98167 20″ Marathon 800 Carpet Extractor (8 Gallon, 230V)
• Tornado 98168 12 Gallon Self Contained Carpet Extractor
• Tornado 98168 20″ Marathon 1200 Carpet Extractor (12 Gallon, 115V) — all series
• Tornado 98169 20″ Marathon 1200 Carpet Extractor (12 Gallon, 230V)

A bent or loose bracket moves the spray bar, and a spray bar out of position puts solution in the wrong place. Too far forward and it lands ahead of the brush where the nozzle never recovers it, leaving the carpet wet. Too far back and it goes down behind the brush with no agitation at all. Either way the operator reports poor cleaning and a wet result, and the spray tips get blamed.

Diagnose by watching rather than guessing. Run clean water through the spray system with the machine tipped and look at where the fan actually strikes relative to the brush. It should land just ahead of the bristles across the full width. A pattern that is correct at one end and drifting at the other points at the bracket, not at the tips.

The bracket gets damaged by impact from below — kerbs, thresholds, a machine set down hard — and by being used as a handhold when tipping the machine. Because it is a welded assembly, straightening it tends to move the geometry somewhere else rather than restoring it, so a bent one is a replacement rather than a repair.

Check the fasteners as well as the metal. A bracket that is sound but working loose does the same thing intermittently, which is worse to diagnose: the machine cleans correctly on a flat floor and badly on a ramp, because the manifold shifts under load.

Fit with the machine unplugged, tipped and supported. Photograph the manifold position before anything comes off and set the new bracket to it, then run clean water through and check the fan lands where it should across the full width before the machine goes back into service.

Browse every assembly for this machine on the Tornado 98168 Marathon 1200 parts hub, and see the manufacturer’s range at tornadovac.com.

Frequently Asked Questions

What Tornado machines does the manifold retaining bracket weldment 19152 fit?

It is used on the Tornado 98164 MWH-800 8-gallon self-contained extractor, the 98166 and 98167 20″ Marathon 800, the 98168 12 Gallon Self Contained extractor and the 98168 20″ Marathon 1200 in all series. Call 763-535-0770 with your model number if you are not sure.

How do I tell whether the problem is the bracket or the spray tips?

Run clean water through the spray system with the machine tipped and watch where the fan actually strikes relative to the brush. It should land just ahead of the bristles across the full width. A pattern correct at one end and drifting at the other is the bracket; a gap or a heavy patch in one spot is a tip.

Can a bent bracket be straightened?

Not reliably. It is a welded assembly, so straightening tends to move the geometry somewhere else rather than restoring it. Check the fasteners too — a sound bracket working loose gives the same fault intermittently, cleaning correctly on a flat floor and badly on a ramp.

How do I order the Manifold Retaining Bracket Weldment (part# 19152) or get help?

You can add the Manifold Retaining Bracket Weldment (part# 19152) directly to your cart on this page, or call us at 763-535-0770. Our staff at 5415 West Broadway, Crystal, MN 55428 has been servicing Tornado equipment since 1956 and can help confirm the right part for your machine.

Questions? Call us at 763-535-0770 or visit us at 5415 West Broadway, Crystal, MN 55428.