Find genuine Tornado BDSO 27/28 replacement parts for Models 99786 and 99786C. Can’t find your part? Call us at 763-535-0770.
Find the item number on the drawing, then match it to the same number in the table below that drawing. Each table lists the part description and Tornado’s part number for every numbered item on that sheet.
Brush Base Control — Up to S/N 21000074
This drawing covers machines up to serial number 21000074.
1. Lock Nut INOX – 6022120210. Brushes Base Control Arm – 2060304011. Nut – 6021120112. Articulation Head – 6145120113. E-Clip – 6212080213. E-Clip – 6212080214. Acuator Pin – 2150304015. Brush Actuator Motor – 463200702. Bushing – 471080103. Arm – 208030204. Washer – 603120065. Screw M12 x 40 INOX – 601112206. Lock Nut INOX – 602212027. Washer – 603130038. Articulation Head – 614512029. Screw M12 x 40 INOX – 60111220The brush base control assembly is the mechanism that raises and lowers the scrub deck. On the BDSO 27/28 that means an actuator, its linkage and the pivots and pins the linkage runs on. When a deck will not lift, or lifts slowly and drops under its own weight, the fault is nearly always here rather than in the brush base itself. Worn pins and bushings also let the deck sit unevenly, which shows up as uneven brush wear across the path. Tornado revised this assembly at S/N 21000075, adding a callout; match your serial number before ordering.
| # | Image | Part Description | Part Number | Price |
|---|---|---|---|---|
| 1 | ![]() | Lock Nut INOX | 60221202 | $1.99 |
| 2 | Bushing | 47108010 | Call 763-535-0770 | |
| 3 | Arm | 20803020 | Call 763-535-0770 | |
| 4 | ![]() | Washer | 60312006 | $2.99 |
| 5 | Screw M12 x 40 INOX | 60111220 | Call 763-535-0770 | |
| 6 | ![]() | Lock Nut INOX | 60221202 | $1.99 |
| 7 | ![]() | Washer | 60313003 | $1.99 |
| 8 | Articulation Head | 61451202 | Call 763-535-0770 | |
| 9 | Screw M12 x 40 INOX | 60111220 | Call 763-535-0770 | |
| 10 | Brushes Base Control Arm | 20603040 | Call 763-535-0770 | |
| 11 | Nut | 60211201 | Call 763-535-0770 | |
| 12 | Articulation Head | 61451201 | Call 763-535-0770 | |
| 13 | ![]() | E-Clip | 62120802 | $1.99 |
| 14 | Acuator Pin | 21503040 | Call 763-535-0770 | |
| 15 | ![]() | Brush Actuator Motor | 46320070 | $627.99 |
| — | Actuator Rod | 63802003 | Call 763-535-0770 |
Brush Base Control — From S/N 21000075
This drawing covers machines from serial number 21000075 forward.
1. Lock Nut INOX – 6022120210. Brush Base Control Arm – 2060604011. Nut – 6021120112. Articulation Head – 6145120113. Spring – 6212000213. Spring – 6212000214. Actuator Pin – 2170303015. Brush Actuator – 4632011016. Pin – 2070312017. Clip – 608000032. Bushing – 471080103. Arm – 208030204. Washer – 603120065. Screw M12 x 40 INOX – 601112206. Lock Nut INOX – 602212027. Washer – 603130038. Articulation Head – 614512029. Screw M12 x 40 INOX – 60111220| # | Image | Part Description | Part Number | Price |
|---|---|---|---|---|
| 1 | ![]() | Lock Nut INOX | 60221202 | $1.99 |
| 2 | Bushing | 47108010 | Call 763-535-0770 | |
| 3 | Arm | 20803020 | Call 763-535-0770 | |
| 4 | ![]() | Washer | 60312006 | $2.99 |
| 5 | Screw M12 x 40 INOX | 60111220 | Call 763-535-0770 | |
| 6 | ![]() | Lock Nut INOX | 60221202 | $1.99 |
| 7 | ![]() | Washer | 60313003 | $1.99 |
| 8 | Articulation Head | 61451202 | Call 763-535-0770 | |
| 9 | Screw M12 x 40 INOX | 60111220 | Call 763-535-0770 | |
| 10 | Brush Base Control Arm | 20606040 | Call 763-535-0770 | |
| 11 | Nut | 60211201 | Call 763-535-0770 | |
| 12 | Articulation Head | 61451201 | Call 763-535-0770 | |
| 13 | Spring | 62120002 | Call 763-535-0770 | |
| 14 | ![]() | Actuator Pin | 21703030 | $30.99 |
| 15 | ![]() | Brush Actuator | 46320110 | $816.99 |
| 16 | Pin | 20703120 | Call 763-535-0770 | |
| 17 | ![]() | Clip | 60800003 | $1.99 |
Frequently Asked Questions About the Tornado BDSO 27/28 Brush Base Control
My deck will not raise. Is that the actuator or a switch?
Listen when you press the lift control. If the actuator runs and the deck does not move, the linkage or a pin has failed. If nothing runs at all, the fault is more likely electrical — the switch, a relay or the harness shown on the control panel and wiring pages.
Why are my brushes wearing unevenly across the path?
Often because worn pivots in the brush base control let the deck hang out of level. Check the pins and bushings on this drawing before you replace brushes again.
Which revision of this assembly do I have?
Machines up to S/N 21000074 use the earlier drawing; machines from S/N 21000075 forward use the later one. Both appear on this page with their ranges stated.
Not sure which brush base control part your machine takes? Call 763-535-0770 with the serial number from the data plate, or stop in at 5415 West Broadway, Crystal, MN 55428 — we have sold and serviced commercial floor equipment since 1956. You can also go back to all Tornado BDSO 27/28 parts diagrams or browse the Tornado BDSO 27/28 parts category.








