Tornado Power Cord 14/3 x 25′ Yellow 32216

$13.99

Genuine Tacony OEM 25-foot 14/3 yellow power cord (part# 32216) for Tornado self-contained carpet extractors — fits the 98164 MWH-800, the 98166 Marathon 800 and both 98168 Marathon 1200 builds. In stock in Crystal, MN. Call 763-535-0770.

The Tornado Power Cord 14/3 x 25′ Yellow (part# 32216) is the genuine Tacony OEM supply cord fitted to Tornado self-contained carpet extractors. It is 25 feet of 14-gauge three-conductor cable in high-visibility yellow — the gauge matters, because these machines run a vacuum motor, a brush motor and a solution pump off one cord, and a thinner replacement will drop voltage and run everything hot. The yellow jacket is not cosmetic either: on a job site the operator needs to see the cord to avoid running the machine over it.

Compatible Models for the Power Cord 14/3 x 25′ Yellow

Fits these Tornado carpet extractors:

  • Tornado 98168 20″ Marathon 1200 Carpet Extractor (12 Gallon 115V) — all series
  • Tornado 98168 12 Gallon Self Contained Carpet Extractor
  • Tornado 98166 20″ Marathon 800 Carpet Extractor (8 Gallon 115V)
  • Tornado 98164 MWH-800 8-Gallon Self-Contained Carpet Extractor

Cords fail at two places and almost nowhere else. The first is the strain relief where the cord enters the machine: constant flexing at that point breaks conductors inside an intact-looking jacket, and the symptom is a machine that cuts out when someone nudges the cord. The second is anywhere the cord has been run over, pinched in a doorway or dragged across a threshold — look for a flattened section, a nick that shows colour through the yellow, or a warm spot after a run. Any of those means replace, not tape.

A cord is also the first thing to rule out when a machine is completely dead. Before you suspect the switch panel, the breaker or the wiring harness, check that the cord has continuity on all three conductors and that the ground pin is still present and tight. A missing ground pin — snapped off and never replaced — is common on rental machines and is a genuine safety fault on a wet machine.

Fitting is straightforward with the machine unplugged. Release the strain relief, note which conductor lands on which terminal before you remove anything, and make sure the new cord is fully seated in the strain relief before you tighten it. A cord clamped on its jacket is right; a cord clamped on its conductors is the reason the next one fails early.

Twin City Vacuum has been selling and servicing Tornado equipment since 1956 and stocks genuine Tacony parts rather than generic substitutes. Browse every assembly for this machine on the Tornado 98168 Marathon 1200 parts hub, and see the manufacturer’s range at tornadovac.com.

Frequently Asked Questions

What does the Power Cord 14/3 x 25′ Yellow do on a Tornado Marathon extractor?

It is the machine’s only supply cord — 25 feet of 14-gauge three-conductor cable feeding the vacuum motor, brush motor and solution pump. The 14-gauge rating is sized for that combined load; a lighter cord will overheat.

How do I know if my Power Cord (part# 32216) needs replacing?

Look at the strain relief first. If the machine cuts out when the cord is moved, a conductor has broken inside the jacket. Also replace on sight if the cord has been run over, pinched or nicked, if a section feels warm after use, or if the ground pin is missing or loose.

What models is the Power Cord 14/3 x 25′ Yellow (part# 32216) compatible with?

It fits the Tornado 98168 20″ Marathon 1200 Carpet Extractor (12 Gallon 115V) — all series, the Tornado 98168 12 Gallon Self Contained Carpet Extractor, the Tornado 98166 20″ Marathon 800 Carpet Extractor (8 Gallon 115V) and the Tornado 98164 MWH-800 8-Gallon Self-Contained Carpet Extractor. Not sure which machine you have? Call us at 763-535-0770 with your model and serial number and we will confirm it before you order.

How do I order the Power Cord 14/3 x 25′ Yellow (part# 32216) or get help?

You can add the Power Cord 14/3 x 25′ Yellow (part# 32216) directly to your cart on this page, or call us at 763-535-0770. Our staff at 5415 West Broadway, Crystal, MN 55428 has been servicing Tornado equipment since 1956 and can help confirm the right part for your machine.

Questions? Call us at 763-535-0770 or visit us at 5415 West Broadway, Crystal, MN 55428.