Tornado Shroud Pivot Bushing 19153

The pivot bushing is the bearing surface the brush shroud swings on. It takes the whole weight of the shroud every time it is opened and closed, and it does so in standing detergent. Part number 19153 is the genuine OEM shroud pivot bushing for the MWH-800, Marathon 800 and Marathon 1200 extractors.

Compatible Models for the Shroud Pivot Bushing

This part fits the following Tornado machines:

• Tornado 98164 MWH-800 8-Gallon Self-Contained Carpet Extractor
• Tornado 98166 20″ Marathon 800 Carpet Extractor (8 Gallon, 115V)
• Tornado 98167 20″ Marathon 800 Carpet Extractor (8 Gallon, 230V)
• Tornado 98168 12 Gallon Self Contained Carpet Extractor
• Tornado 98168 20″ Marathon 1200 Carpet Extractor (12 Gallon, 115V) — all series
• Tornado 98169 20″ Marathon 1200 Carpet Extractor (12 Gallon, 230V)

A worn bushing lets the shroud drop. Not dramatically — a millimetre or two — but that is enough to open a gap along one edge when the latch is closed, and a gap there costs suction at the nozzle with nothing visibly wrong anywhere else. People chase that fault through hoses, filters and tank gaskets without ever looking at the pivot.

Check it directly. With the shroud closed and latched, lift its free edge: any vertical play means something in the pivot has gone. Then open the shroud fully and try to rock it side to side at the hinge. A sound bushing allows almost none. If the shroud also feels notchy or stiff rather than swinging freely, the bushing has picked up grit.

Grit is the real enemy here. Carpet fibre and sand work into the pivot, and every open-and-close cycle laps the bushing a little more. Rinsing the pivot area rather than just wiping it, and doing so before the machine is put away rather than after the grit has dried in, roughly doubles how long a bushing lasts.

Replace both sides at once if the machine has two. They see identical duty, so a bushing that has worn out has a twin that is nearly there, and the labour of getting to the second one later costs far more than the part.

Fit with the machine unplugged, tipped and supported. Clean the pivot bore properly before the new bushing goes in — fitting a new bushing over packed grit destroys it quickly. Reassemble, close the latch and check the gap along the shroud edge is even before the machine goes back to work.

Browse every assembly for this machine on the Tornado 98168 Marathon 1200 parts hub, and see the manufacturer’s range at tornadovac.com.

Frequently Asked Questions

What Tornado machines does the shroud pivot bushing 19153 fit?

It is used on the Tornado 98164 MWH-800 8-gallon self-contained extractor, the 98166 and 98167 20″ Marathon 800, the 98168 12 Gallon Self Contained extractor and the 98168 20″ Marathon 1200 in all series. Call 763-535-0770 with your model number if you are not sure.

How do I know the pivot bushing is worn?

With the shroud closed and latched, lift its free edge — any vertical play means the pivot has gone. Then open the shroud fully and try to rock it side to side at the hinge; a sound bushing allows almost none. A shroud that feels notchy rather than swinging freely has picked up grit.

Can a worn pivot bushing really cost me suction?

Yes, and it is easy to miss. A bushing that lets the shroud drop a millimetre or two opens a gap along one edge when the latch is closed, and that gap costs suction at the nozzle with nothing visibly wrong in the hose, the filter or the tank gasket.

How do I order the Shroud Pivot Bushing (part# 19153) or get help?

You can add the Shroud Pivot Bushing (part# 19153) directly to your cart on this page, or call us at 763-535-0770. Our staff at 5415 West Broadway, Crystal, MN 55428 has been servicing Tornado equipment since 1956 and can help confirm the right part for your machine.

Questions? Call us at 763-535-0770 or visit us at 5415 West Broadway, Crystal, MN 55428.