Tornado BDSO 27/28 Stand-On Scrubber Parts
Shop genuine Tornado BDSO 27/28 parts for the stand-on scrubber, models 99786 and 99786C. This category covers every assembly in Tornado’s current parts listing for the machine — brush base and brush base control, brush base transmission, squeegee and squeegee control, recovery tank, solution tank, water valve and water filter, vacuum and suction, drive wheel control, steering wheel, frame, foot board, lower and rear covers, rear wheel, battery charger, and the electrical layout, block and detailed wiring diagrams. Order online, or call us at 763-535-0770 with your serial number and we will confirm the right part.
Tornado BDSO 27/28 Parts: Finding the Right One for Your Serial Number
The BDSO 27/28 has had a long production run, and Tornado revised several of its assemblies along the way. The brush base, control panel, squeegee control, steering wheel, drive wheel control, vacuum, recovery tank, solution tank, electrical layout and wiring all have more than one drawing, each covering a different block of serial numbers. A part that is correct for an early machine is often superseded on a later one, which is why the serial number stamped on your machine matters as much as the model number when you order. Each of our schematic pages shows every revision Tornado publishes, in serial order with the range stated above the drawing, so you can match your machine before you add anything to the cart.
The parts that move most on a stand-on scrubber are the ones in contact with the floor and the water: squeegee blades, brushes and pad drivers, the vacuum motor and its gasket, solution and recovery tank seals, the water valve and the water filter screen. Drive and steering components — the drive wheel control assembly, the steering wheel assembly and its cables — wear more slowly, but they are the parts that take a machine out of service when they fail. Electrical faults usually trace back to a switch, relay, contactor or harness shown on the electrical layout and detailed wiring diagram pages.
Twin City Vacuum has sold and serviced commercial floor equipment from 5415 West Broadway in Crystal, Minnesota since 1956. If you are not sure which assembly your part sits in, call 763-535-0770 — it is faster than guessing from a drawing. You can also browse the full Tornado cleaning equipment parts catalog, or see Tornado’s own product information at tornadovac.com.
Frequently Asked Questions About Tornado BDSO 27/28 Parts
Which models do these parts fit?
They are listed for the Tornado BDSO 27/28 stand-on scrubber, models 99786 and 99786C. Some individual parts are shared with other Tornado machines; each product page lists every model it fits.
Why does one assembly have more than one drawing?
Tornado revised several BDSO 27/28 assemblies during production. Each drawing covers a block of serial numbers, and the range is stated above the drawing on every schematic page. Check the serial number on your machine, then use the matching drawing.
Where is the serial number on my BDSO 27/28?
On the machine’s data plate. If you cannot read it or cannot find it, call 763-535-0770 and we will help you identify the machine from what you can see.
Can you help me identify a part I cannot find on a drawing?
Yes. Call 763-535-0770 or stop by 5415 West Broadway, Crystal, MN 55428. Our staff has worked on commercial floor equipment since 1956 and can identify a part from a photo or from the old part itself.
Choosing the right Tornado BDSO 27/28 parts
The Tornado BDSO 27/28 is the larger machine in this stand-on family, sold as models 99786 and 99786C. It runs a wider twin-disc deck than the BDSO 20/21, so while the two machines share a family resemblance they do not share a parts book — always check the part number before ordering across the two. Most Tornado BDSO 27/28 parts are common to both the 99786 and the 99786C; where a part changed during the production run, the assembly page shows each revision as a labelled block in serial order, oldest first.
Wear on this machine concentrates where you would expect it. Pad drivers and brushes go first, then squeegee blades, then the solution valve and the vacuum motor filter. The drive wheel, the brush base bearings and the squeegee castors follow. Those are the Tornado BDSO 27/28 parts most operators keep on the shelf, and they are the ones worth checking at every service rather than waiting for a fault. Electrical faults on this machine are usually traced through the detailed wiring diagram and the block diagram rather than the mechanical assemblies, and both of those sheets are published here with every callout clickable.
Every numbered callout on each of the twenty-three assembly diagrams is linked to the part it belongs to, and every part carries its own page with fitment, price and availability. Where the factory does not sell an item separately, the row stays on the table marked call-us so the numbering always matches the drawing. If you cannot find what you need, call 763-535-0770 with your model and serial number — we have been servicing commercial floor equipment at 5415 West Broadway, Crystal, MN 55428 since 1956.
Tornado BDSO 27/28 parts: frequently asked questions
Do Tornado BDSO 27/28 parts fit the 99786 and the 99786C?
In most cases yes. The 99786 and 99786C share the great majority of their assemblies. Where a difference exists it is called out on the relevant assembly page, and the serial-number blocks on that page show which version applies to your machine.
Can I use Tornado BDSO 20/21 parts on a BDSO 27/28?
Only where the part number is identical. The two machines are different deck sizes with different parts books, and many parts that look similar carry different numbers. Check the number on the diagram rather than the appearance of the part.
Why do some rows on the diagrams show call us instead of a price?
Those are parts the factory does not supply to us separately. We leave the row on the table so the numbering matches the drawing, and we can normally still source the item — call 763-535-0770 with the callout number and your serial number.
See every Tornado BDSO 27/28 parts diagram, browse the wider Tornado cleaning equipment parts range, or compare Tornado BDSO 20/21 parts for the smaller machine in the same family. Manufacturer specifications are published at tornadovac.com.
Showing 41–60 of 292 results
-

Drain Hose Plug Tie Rod 39 mm 20110170
$14.99 -

Drain Plug Assembly V0110008
$54.99 -

Drain Plug Lever 61820003
$6.99 -

Drive Direction Manipulator 63407001
$113.99 -

E-Clip 62120802
$1.99 -

Elbow Fitting 62320020
$25.99 -

Eye Support 63714002
$1.99 -

Flat Washer M6 60306008
$1.99 -

Float Filter Assembly V0110007
$24.99 -

Frame Cap 20701080
$23.99 -

Front Cover Bushing 47115030
$13.99 -

Fuse 100A 62810001
$18.99 -

Fuse 20A 62802002
$1.99 -

Fuse 30A Maxi 62803001
$3.99 -

Fuse 3A 62800301
$1.99 -

Gas Shock Absorber 49120070
$101.99 -

Gas Shock Absorber Support 61001001
$28.99 -

Gasket 62370004
$4.99 -

Handwheel 61710003
$9.99 -

Handwheel 61712002
$15.99
