Find genuine Tornado BDSO 27/28 replacement parts for Models 99786 and 99786C. Can’t find your part? Call us at 763-535-0770.
Find the item number on the drawing, then match it to the same number in the table below that drawing. Each table lists the part description and Tornado’s part number for every numbered item on that sheet.
Squeegee Drawing
Tornado publishes one drawing for this assembly, covering every BDSO 27/28 serial number.
1. Nut Cover – 6204000110. Wing Nut – 6170600411. Dowel INOX – 6016060712. Front Squeegee Rubber (35.43 x 1.97") – 4841502013. Nut INOX – 6021060114. Squeegee Body – 4821501015. Nut INOX – 6021120316. Dowel – 6016120017. Washer – 6031200618. Handwheel – 6171200219. Rear Squeegee Rubber (37.60" x 3.54" x.19") – 484150102. Lock Nut – 6022080320. Rear Squeegee Blade Holder – 2150401020. Rear Squeegee Blade Holder – 2150401021. Washer INOX – 6030801021. Washer INOX – 6030801022. Wing Nut – 6170800822. Wing Nut – 6170800823. Screw M3 x 10 INOX – 6015030323. Screw M3 x 10 INOX – 6015030324. Rear Center Squeegee Blade – 4830802025. Lock Nut – 6022030225. Lock Nut – 6022030226. Adjustable Latch Assembly – 6220000526. Adjustable Latch Assembly – 6220000527. Screw M6 x 60 INOX – 6014061027. Screw M6 x 60 INOX – 6014061028. Rear Center Squeegee Blade Assembly – V830705029. Squeegee Assembly – V82150103. Washer INOX – 603080104. Bumper Wheel – 465410105. Bushing – 471010406. Bushing – 471060607. Lower Squeegee Bumper Wheel – 465110608. Screw M8 x 70 INOX – 601108379. Front Squeegee Blade – 48315010The squeegee is what makes a scrubber a scrubber: it pulls the dirty water off the floor so the vacuum can lift it. This drawing covers the squeegee frame, the front and rear blades, the clamp or retainer that holds them, the casters or wheels that set the trailing angle, and the hardware. Blades are the fastest-wearing parts on the entire machine — they round over at the working edge and start leaving a film or streak long before they look worn out. If pickup has gone soft, look at the blades and the casters here before you suspect the vacuum motor.
| # | Image | Part Description | Part Number | Price |
|---|---|---|---|---|
| 1 | ![]() | Nut Cover | 62040001 | $1.99 |
| 2 | ![]() | Lock Nut | 60220803 | $1.99 |
| 3 | ![]() | Washer INOX | 60308010 | $1.99 |
| 4 | ![]() | Bumper Wheel | 46541010 | $9.99 |
| 5 | ![]() | Bushing | 47101040 | $8.99 |
| 6 | ![]() | Bushing | 47106060 | $10.99 |
| 7 | ![]() | Lower Squeegee Bumper Wheel | 46511060 | $19.99 |
| 8 | ![]() | Screw M8 x 70 INOX | 60110837 | $2.99 |
| 9 | ![]() | Front Squeegee Blade | 48315010 | $60.99 |
| 10 | ![]() | Wing Nut | 61706004 | $3.99 |
| 11 | Dowel INOX | 60160607 | Call 763-535-0770 | |
| 12 | ![]() | Front Squeegee Rubber (35.43 x 1.97") | 48415020 | $53.99 |
| 13 | ![]() | Nut INOX | 60210601 | $1.99 |
| 14 | ![]() | Squeegee Body | 48215010 | $671.99 |
| 15 | ![]() | Nut INOX | 60211203 | $1.99 |
| 16 | Dowel | 60161200 | Call 763-535-0770 | |
| 17 | ![]() | Washer | 60312006 | $2.99 |
| 18 | ![]() | Handwheel | 61712002 | $15.99 |
| 19 | ![]() | Rear Squeegee Rubber (37.60" x 3.54" x.19") | 48415010 | $63.99 |
| 20 | Rear Squeegee Blade Holder | 21504010 | Call 763-535-0770 | |
| 21 | ![]() | Washer INOX | 60308010 | $1.99 |
| 22 | ![]() | Wing Nut | 61708008 | $10.99 |
| 23 | ![]() | Screw M3 x 10 INOX | 60150303 | $1.99 |
| 24 | ![]() | Rear Center Squeegee Blade | 48308020 | $78.99 |
| 25 | ![]() | Lock Nut | 60220302 | $1.99 |
| 26 | ![]() | Adjustable Latch Assembly | 62200005 | $29.99 |
| 27 | ![]() | Screw M6 x 60 INOX | 60140610 | $1.99 |
| 28 | ![]() | Rear Center Squeegee Blade Assembly | V8307050 | $163.99 |
| 29 | Squeegee Assembly | V8215010 | Call 763-535-0770 |
Frequently Asked Questions About the Tornado BDSO 27/28 Squeegee
How often should I replace squeegee blades on a BDSO 27/28?
There is no interval — it depends on your floor. Flip or rotate a blade when it starts streaking and replace it when both working edges are rounded. A blade that leaves a line behind the machine is already worn out even if it looks intact.
My machine streaks on one side only. What causes that?
Usually a damaged section of blade, a caster that has worn unevenly, or debris caught in the squeegee frame. All three are on this drawing. Check the frame is sitting square to the floor across its whole width.
Is the squeegee assembly the same across all serial numbers?
Yes. Tornado publishes one squeegee drawing for the BDSO 27/28. The squeegee control assembly — the mechanism that raises and lowers it — is a separate page with four revisions.
Not sure which squeegee part your machine takes? Call 763-535-0770 with the serial number from the data plate, or stop in at 5415 West Broadway, Crystal, MN 55428 — we have sold and serviced commercial floor equipment since 1956. You can also go back to all Tornado BDSO 27/28 parts diagrams or browse the Tornado BDSO 27/28 parts category.
























